Re-understanding the Scientific Significance of Friction Coefficient in Roll Packaging Materials – Haide Packaging's Technical Perspective

Mar 05, 2026 Leave a message

In the flexible packaging industry, the friction coefficient of roll packaging materials has always been a key focus for both producers and users. Whether it is upstream companies requiring low friction coefficients when purchasing heat-sealable substrates, or downstream pharmaceutical and food factories testing the smoothness performance when receiving packaging materials, both reflect the industry's common pursuit of smooth operation in automated packaging.

However, for a long time, there have been certain misunderstandings and deviations in the industry's understanding and testing methods regarding friction coefficients. Based on years of practical experience and technical research, Haide Packaging systematically reviews and clarifies this topic here.

I. The Essence of Friction Coefficient and Current Testing Practices

In physics, the friction coefficient (μ) is defined as the ratio of friction force (f) to vertical pressure (N), i.e., μ = f / N. In the practical application of packaging materials, it involves the "friction pair" system formed by the material surface and its contacting object.

The following testing habits are prevalent in the industry:

When purchasing heat-sealable substrates, the friction coefficient between their heat-seal surfaces is tested (referred to as the "substrate inner/inner-cold friction pair").

When delivering finished roll materials, the friction coefficient between the heat-seal surfaces of the composite film is tested (referred to as the "composite film inner/inner-cold friction pair").

Both tests are conducted at room temperature, but their results do not truly reflect the actual performance of the material on automated packaging machines. Haide Packaging research shows that what downstream customers truly need is the smoothness performance of the packaging material under actual operating conditions, not the self-friction data of the material surface at room temperature.

II. Real Friction Scenarios in Automated Packaging Machines

The operating environment of automated packaging machines is complex, with various types of friction pairs:

Inner/metal friction pair: Packaging material heat-seal surface and stainless steel forming surface.

Outer/metal friction pair: Packaging material outer surface and stainless steel forming surface.

Outer/rubber friction pair: Packaging material outer surface and rubber synchronous belt.

Some equipment may not even have sliding friction parts.

More importantly, continuous operation of the equipment leads to an increase in temperature at friction points (often exceeding 40°C), forming a "hot friction pair." Therefore, when evaluating the smoothness of packaging materials, attention should be paid to the friction coefficient between the material and a metal surface at a certain temperature, rather than the self-friction data of the material at room temperature.

III. The Key Impact of Temperature on Friction Performance

According to the group standard T/CAB 0122-2021 "Technical Requirements for Surface Smoothness of Paper Packaging Prints," smoothness should comprehensively consider dynamic and static friction coefficients, with particular attention to the impact of temperature.

Experimental data shows:

Heat-sealable substrate (CPP, CPE) inner/inner-cold friction coefficient: 0.1–1.0.

Same material inner/metal-cold friction coefficient: 0.17–0.25.

At 40°C, the inner/metal-hot friction coefficient varies in the range: 0.13–0.3.

Common slip agents (oleamide and erucamide) have melting points of 72–77°C and 78–81°C, respectively. When the equipment surface temperature rises due to continuous friction or heating devices, the slip agent softens and migrates, leading to an increase in the friction coefficient, ultimately manifesting as poor operational smoothness.

IV. Haide Packaging's Practical Recommendations

Based on the above analysis, Haide Packaging proposes the following recommendations for the industry:

1. Establish a Correct Evaluation System

Stop the simplistic pursuit of "low friction coefficient materials."

Clearly specify the type of friction pair and temperature conditions during evaluation.

Inner/inner-cold friction data cannot represent actual performance in use.

2. Optimize Procurement and Testing Standards

When purchasing heat-sealable substrates, focus on evaluating their inner/metal-hot friction coefficient (recommended ≤0.3).

Before delivering finished products, test the actual friction performance of the packaging material under simulated operating temperatures.

For special equipment (with no sliding friction or only outer/metal friction), unnecessary friction coefficient testing clauses can be omitted.

3. Promote Industry Standard Upgrades

Recommend that relevant associations and companies consider actual operating conditions when revising standards.

Establish a classified evaluation method based on equipment type and operating conditions.

V. Conclusion

The management of friction coefficients for roll packaging materials should not remain at the level of traditional testing but should delve into understanding the actual operating environment of automated packaging. Through continuous technical research and practical experience, Haide Packaging has established a comprehensive friction performance evaluation and application system, providing customers with full-process solutions from material selection and process optimization to usage guidance.

We look forward to working with industry partners to promote the scientific development of packaging material evaluation systems, ensuring that every roll of material operates smoothly on high-speed automated packaging lines.

Send Inquiry

whatsapp

Phone

E-mail

Inquiry